HARMAN KARDON AVR235
Owner's Manual

OPERATION
lower frequency station with acceptable signal strength. An AUTO ST TUNED indication will momentarily appear when the station stops at a stereo FM station, and an AUTO TUNED indication will momentarily appear when an AM or monaural FM station is tuned. Press the Tuning buttons again to scan to the next receivable station. When the button is pressed so that MANUAL appears in the Lower Display Line ¯ each tap of the Selector will increase or decrease the frequency by one increment. When the tuner receives a strong enough signal for adequate reception, MANUAL TUNED will appear in the Lower Display Line ¯. 4. Stations may also be tuned directly in either the automatic or manual mode. To enter a station�s frequency directly, first select the AM or FM band as desired be pressing the AM/FM Tuner Select Button g!. Next, press the Direct Button t. Within five seconds of when DIRECT IN scrolls in the Upper Display Line �, enter the station frequency by pressing the Numeric Keys r. If you press an incorrect button while entering a direct frequency, press the Clear Button 35 to start over. NOTE: When the FM reception of a station is weak, audio quality will be increased by switching to Mono mode by pressing the Tuner Mode Button &s so that MANUAL appears momentarily in the Lower Display Line ¯ and then goes out. This will also activate manual tuning mode. Preset Tuning Using the remote, up to 30 stations may be stored in the AVR 235�s memory for easy recall using the frontpanel controls or the remote. To enter a station into the memory, first tune the station using the steps outlined above. Then: 1. Press the Memory Button 48 on the remote. The two underscore lines will appear at the far right side of the Upper Display Line �. 2. Within five seconds, press the Numeric Keys r corresponding to the location where you wish to store this station�s frequency. Once entered, the preset number will appear in the Upper Display Line �. 3. Repeat the process after tuning any additional stations to be preset. Recalling Preset Stations � To manually select a station previously entered in the preset memory, press the Numeric Keys r that correspond to the desired station�s memory location. � To manually tune through the list of stored preset stations one by one, press the Preset Stations Selector Buttons $ 34 on the front panel or remote. Adjust the level using the �/¤ Buttons n until the LED lights green for all channels. When it is red, the level is too high; when it is amber, the level is too low. Press the SPL Selector Button 40 to turn the sensor and indicator off. If you prefer, you may use a handheld SPL meter to guide you to the correct SPL levels. Set the meter to the C-Weighting Slow scale, and adjust the volume until the meter reads 75dB. Once the reference level has been set, press the Channel Select Button m and FRONT L LEV will appear in the Lower Display Line ¯. To change the level, first press the Set Button p, and then use the �/¤ Buttons n to raise or lower the level. DO NOT use the volume control, as this will alter the reference setting. Once the change has been made, press the Set Button p and then press the �/¤ Buttons n to select the next output channel location that you wish to adjust. To adjust the subwoofer level, press n the �/¤ Buttons until WOOFER LEV appears in the Lower Display Line ¯. Repeat the procedure as needed until all channels requiring adjustment have been set. When all adjustments have been made and no further adjustments are made for five seconds, the AVR 235 will return to normal operation. The channel output for any input may also be adjusted using the full-OSD on-screen menu system. First, set the volume to a comfortable listening level using the Volume Control � 38 . Then, press the OSD Button v to bring up the MASTER MENU (Figure 1). Press the ¤ Button n until the onscreen � cursor is next to the CHANNEL ADJUST line. Press the Set Button p to activate the CHANNEL ADJUST menu. Once the menu appears on your video screen, first use the �/¤ Buttons n to move the on-screen � cursor so that it is next to the TEST TONE line. Press the � / � Buttons o so that OFF appears. This will turn off the test tone and allow you to use your external test disc or other source material as the reference. Then, use the �/¤ Buttons n to select the channels to be adjusted. At each channel position, use the � / � Buttons o to change the output level. Remember, the goal is to have the output level at each channel equal when heard at the listening position. If you wish to reset all the levels to their original factory default of 0dB offset, press the �/¤ Buttons n so that the on-screen cursor is next to the CHANNEL RESET line and press the � / � Buttons o so that the word ON appears. After the

Recording
In normal operation, the audio or video source selected for listening through the AVR 235 is sent to the record outputs. This means that any program you are watching or listening to may be recorded simply by placing machines connected to the Tape Outputs � or Video 1/Video 2 Audio and Video Outputs eh 32 34 in the Record mode. When a digital audio recorder is connected to the Digital Audio Outputs �°, you are able to record the digital signal using a CD-R, MiniDisc or other digital recording system. NOTES: � The digital outputs are active only when a digital signal is present, and they do not convert an analog input to a digital signal, or change the format of the digital signal. In addition, the digital recorder must be compatible with the output signal. For example, the PCM digital input from a CD player may be recorded on a CD-R or MiniDisc, but Dolby Digital or DTS signals may not. � Please make certain that you are aware of any copyright restrictions on any material you copy. Unauthorized duplication of copyrighted materials is prohibited by federal law.

Output Level Trim Adjustment
Normal output level adjustment for the AVR 235 is established using the test tone, as outlined on pages 23�24. In some cases, however, it may be desirable to adjust the output levels using program material such as a test disc, or a selection you are familiar with. Additionally, the output level for the subwoofer can only be adjusted using this procedure. To adjust the output levels using program material, first set the reference volume for the front left and front right channels using the Volume Control � 38 î. If you are using a disc with test signals or an external signal generator as the source from which to trim the output levels, you may use the EzSet feature of the remote to guide you to the correct SPL level. To use the remote for this purpose, press and quickly release the SPL Selector Button 40 to activate the sensor. While the test tone is circulating, the Program/SPL Indicator c will change color to indicate the level.

30

OPERATION